GN’s Slurry drilling mud system

GN Solids Control is probably the largest solid control as well as drilling waste management companies which usually specializes in manufacturing the similar equipment, such as shale shaker, desander, desilter, mud cleaner, vacuum degasser, mud gas separator, decanter centrifuge, agitator, centrifugal pump, cutting dryer, screw pump, shear pump, mud gun and so on. Immediately after 10 years development, GN offers promoted its products to 60 countries and now additionally, it established two overseas subsidiaries, US and Russia.

drilling mud system
Not long ago GN formally introduced the four solid control and also dewatering system, and slurry dredging system is one of these. Now we will introduce typically the configuration and some features to your account. According to the customer’s working situation and requirement, the system can be made into skid fastened or trailer mounted. The actual system mainly consists of the particular course shale shaker, desander, desilter, decanter centrifuge intended for 3 to 6 stages connected with separation according to customer’s demands. The working process is like this specific: the dredged slurry circulated from the pit or water tunnel, first the slurry will go through the scalping shale shaker, the solids such as trash, can, leaves, gemstone and so on will be separated through the slurry and the slurry may drop to a tank, then slurry will be sucked with the centrifugal to the desander, as well as desilter’shydrocyclone, in the hydrocyclone, typically the solids from 20-60 microns will be separated and dismissed and then dropped to the vibrating sex screens for further drying. The particular cleaner slurry will go straight into another tank then become pumped into the decanter centrifuge, and the solids over a couple of microns will be separated and also the cleaner slurry will be wiped away to the system. If possible, there may be another chemical decanter centrifuge to separate the solids near zero microns. The whole tools and configuration could be personalized per customer’s requirement in addition to working condition.
That’s the particular brief introduction of the slurry dredging system. Hopefully it can be useful to you. We will do our utmost to assist your business to be successful. This is visit http://www.gnsolidsamerica.com and please mail your inquiries to USA@gnsolidscontrol. com

GN Solids Control is attending OTC oil show

OTC oil show is much close, which will be hold in 2-5 May, 2016, in Houston, TX, USA. After about 3 month’s preparation, GN Solids Control is ready for the big event now. We have two booths there to deeper our brand influence and we bring our key equipment to show there, including latest model decanter centrifuge, latest model vertical cuttings dryer, High G drying shaker, shaker screen etc. The visitors can feel the high quality and premium technology equipment by touching and watching the real equipment at the event.

1) 14inch bowl size decanter centrifuge
This size centrifuge is most popular as the wide application and good price. The GNLW363 14inch bowl centrifuge is equivalent to Swaco 518 CENTRIFUGE / Derrick DE1000 centrifuge. But the price of USA centrifuge is much higher than our brand. We target on high end market and overseas market. The price is much better when compared with USA brand, but our price is relatively higher than other China brand centrifuge.

OTC 2016

2) GNCD930 vertical cuttings dryer
GNCD930 vertical cuttings dryer is used for drilling cuttings treatment at rigsite or at one mud plant location where all cuttings transport to the center location for final treatment. After treatment of GN vertical cutting s dryer, the oil on cuttings can reduce to below 5%. This is same working performance as CSI dryer or SWACO dryer. GN vertical cuttings dryer already put into market for over 3 years, and the mature product is benefiting more drilling service companies, good price, stable working performance and less maintenance.

3) High G drying shaker
High G drying shale shaker is same as normal shale shaker. Just the G force is bigger. This unit is mostly used for water based mud drilling cuttings treatment. After treated, the oil on cuttings can be reduced to about 10% to 20%.
GN composite material screen, replacement for Swaco Mongoose shaker screen will be also showed at the OTC event.
If you come to the OTC, pls send us email to make an appointment. My email ID: roy@gnsolidscontrol.co, thanks for reading.

More Shale Shaker Screens Just Arrived in Houston

GN Solids Control has established the Houston department company GN Solids America for several years. Although GN Des moines Branch Company is still a fresh company, drilling companies within US, Canada and Paraguay is getting to know GN.
GN Solids America LLC features a large warehouse in Des moines which reaches to thirty three, 000 square feet. Many solids control and drilling waste management systems are in share, such as shale shaker, Mud Gas Separator,mud cleaner, shear pump, decanter centrifuge along with cuttings dryer. Thousands of shaker screens are also stocking throughout Houston warehouse for fast delivery.
GN Solids Control manufactures various shaker displays such as replacement screens intended for Derrick 500 or Derrick 2000 series, replacement projection screens for Swaco Mongoose, alternative screens for NOV VSM 300 or NOV Full Cobra screens.
All GN shaker screens are line mesh weaved and made according to the API RP 13C standard, which is a common typical when name different API nos. GN just opened up another manufacturing plant which pretty closes to GN home office. This new plant will largely manufacture composite material shaker screens.

Composite_Frame_Shaker_Screen
As we usually separate the shaker screens by means of two types: one is metal body shaker screen and the various other is composite frame shaker screen. Composite frame move screen is widely noticed on Mi-Swaco shaker monitors. If you comparing the successful separating area, you will find the upvc composite frame shaker screen possesses more opening area versus the metal frame screen. Along with due to the pretensioned technology, upvc composite material shaerk screens can be utilized longer than the metal framework screens although the composite sort price is a little bit higher.
Through the long run, using composite stuff shaker screens will help to reduce cost for drilling corporations. Many customized shaker projection screens are also provided by GN Solids Control. GN Solids America LLC now is working with quite a few large drilling companies; they help keep purchasing shaker screens via us regularly. GN in addition provides customized logo with all the permission of our clients.

GN Solids Control 4th generation decanter centrifuge release to market

GN Solids Control as China leading manufacturer for solids control equipment, always walks ahead of all solids control companies in China. We just release the 4th generation decanter centrifuge to optimize the user experience and less maintenance.

 

GN Solids Control centrifuge have upgraded from 1st generation, 2nd generation, 3rd generation to 4th generation now. In the past several years, GN Solids Control continuously perfects the unsatisfying points and until 3rd generation, GN centrifuge is working much fine for both solids control equipment & drilling waste management. Even heavy mud with lots of sands/ solids, GN decanter centrifuge can also work well to satisfy our clients.

 

The 4th generation decanter centrifuge with fewer footprints can work even in very compact environment. This centrifuge is much international in outlooks, similar to USA type centrifuge, also similar to Europe type centrifuges.

Mini Decanter Centrifuge

GN decanter centrifuge can be used for oil and gas drilling, drilling mud system, diamond drilling, core well drilling, etc. The most projects is for oil drilling. GN just sold over 30 sets centrifuge to Algeria for oil drilling rigs. GN Solids Control 3TH generation centrifuge is working very fine at Algeria and many people are curious about the high quality of GN centrifuges and want to know how long time the high quality can be kept. Until now, one years past, the centrifuge is still working same as before.

 

Except for decanter centrifuge, GN vertical cuttings dryer is also working very fine at Algeria. Greatwall drilling from CNPC have lots of contract in Algeria for drilling waste management and GWDC bought 5 sets vertical cuttings dryer in 2015 and ship to Algeria for the project. After one year, the vertical cuttings dryer is working fine, the client is satisfy with the treating performance. And finally, GN Solids Control have more chance to do business with national companies.

 

GN Solids Control equipment is working well for many drilling companies, national oil service companies, national mud engineering companies etc. Pls contact us freely if you need some support.

Right after sales free solids control items for old customers

To maintain the good relationship which includes VIP clients, GN Solids Control have plan to check out some big clients in various regions. Our target would be to conclude on the past tasks, do after sales support, offer free solids control items if necessary, and also speak more new project arriving near future. This year, we have drilling to plan to VIP clients within Iran, Kuwait, UAE, Egypt, Nigeria, Russia, USA, South america, Australia, Korea, Argentina and so on The VIP clients will certainly support 80% sales quantity of GN Solids CONTROL . We cherish the long run relationship with the VIP customers, and will improve every year to provide better product and support.

GN Solids Control can produce so fast, one is based on the high quality equipment and great price. The other is based on the fast response after product sales service. Our product happen to be exported to over 60 nations. The sale amount each year may reach to about 20million dollars. The mainly gear including:
decanter centrifuge-2
1) Large quantity associated with decanter centrifuges .
Every year we export more than 250 sets centrifuge along with feeding pumps. About one hundred fifty sets centrifuge for abroad market and about 100 models centrifuge for domestic marketplace. Most popular model centrifuge is actually GNLW363CG or GNLW363CG-VFD. GNLW363CG is GN fixed pace centrifuge, with 3200rpm /2700rpm / 2200rpm speed. GNLW363CG-VFD is GN variable pace centrifuge, with stepless flexible speed from o in order to 3200rpm.

2) Vertical cuttings dryer, not large quantity
The requirements of vertical cuttings dryer is not that higher as decanter centrifuge. We may export regarding 20 sets vertical cuttings dryer for drilling waste management . The actual drilling waste management getting pregnant is also just aroused within past one to two years. GN Solids Control vertical cuttings dryer can work similar because CSI dryer after all of us test the dryer within drilling site.

3) great quantity of pumps

We foreign trade large quantity of centrifugal penis pumps, shear pumps , submersible slurry pumps in order to overseas solids control drilling site and HDD drilling companies.

If you need any solids control equipment and drilling mud system, mud mixing system, pls call us freely.

Bore Pile Construction Mud System

For the bore piling, we have a compact efficient demanding unit design, to separate big particles by the bottom shaker of the double deck shaker, and then separate particles bigger than 75microns by desander, then go through the top deck shaker screen. For different project, may need different screens, sometimes even need big hole sieve screens. While it separate only 75 micron or bigger solids.

Which also means if you need better result, other equipment will be needed, de-silter, decanter centrifuge, or even chemical enhancement system. Also if for environmental protection, may even need drilling waste management unit to make the waste a better way before it is dumped, or shipped to other place.
“Bore Pile Construction Mud System”的图片搜索结果
In some project, may need find a way to make the cutings dryer, like use High -G dryer shaker, to make it easier for truck transportation.
Or sometimes engineers will prefer the whole system, not just a demanding unit, like the compact one for HDD projects. Use shaker for the first step separation, then desander, / desander cleaner, then desolater, then centrifuge.

We also made some customised design for CPP, use double deck cleaners, both shaker are double deck shaker, and top deck used as mud cleaner screening equipment. Then the centrifuge, for cleaning the fluid. It will also be a good modular design.

Nowadays, more and more countries are investing on the civil constructions, subway construction, and so on, which makes the demanding unit more and more popular.
Recently, GN Solids Control shipped several units of Desander Machines for bored pile construction to Asia countries include Saudi Arabia, Myanmar, Singapore and China . This compact design desanding plant is a cost-effective solution for mud recycling for the construction projects. The desander machine can be used for bored pile foundation or TBM as well as the horizontal directional drilling projects.

Related Posts

Shale Shakers for UAE

The UAE drilling company purchased four sedimentary rock shakers and a giant batch of sedimentary rock shaker screens from GN Solids management to interchange their drilling rigs existing sedimentary rock shakers for solids system.

GN Solids management manufacture the High G force sedimentary rock shakers for primary solids management and drilling cuttings drying application. the three panel and four panel sedimentary rock  shakers area unit offered for various comes.Because GN Solids management not solely create prime quality sedimentary rock shakers however additionally give the cost-efficient sedimentary rock shaker screens for our shoppers, this is often one the most reasons for shoppers to shop for sedimentary rock shakers from GN.

Shale Shaker for UAE

Shale Shaker for UAE

Features and edges of GN sedimentary rock Shakers

Patent sedimentary rock shaker deck angle adjustable whereas operating, mechanical deck angle adjustment with reliable performance.

Patent tighten rubber waterproofing for sedimentary rock shaker deck and screen, long life and straightforward replacement.

Shale shaker bottom deck made up of stainless-steel for long service life.

Heat treatment on complete sedimentary rock shaker deck for top G force operation.

Pretensioned shale shaker screen for fast screen replacement

.Famous Brand Vibration Motors : IEC Ex, ATEX and UL Certified

Electrical components: SIEMENS, Schneider Brand

Flexible feeding type including Weir Feed, Top Feed, and Hopper Feed for different applications.

About GN Shale Shaker Screens

shale shaker screen to UAE

shale shaker screen to UAE

GN Solids Control make shale shaker screens according to API standard, and most of the popular brand shale shaker replacement shaker screens are available from GN Solids Control. More over, GN Solids Control provide different types of shale shaker screens include but not limitied to following:

Composite Frame Shale Shaker Screen

Steel Frame Shale Shaker Screen

Hook Strip falt shaker screen.

Pyramid shale shaker screen

 

GN 500 GPM mud recovery system for HDD and CBM rig

500GPM is really a normal size mud recovery system utilized for horizontal directional drilling or CBM drilling rig. China top solids control manufacturer: GN Solids Control offers different plans 500GPM system to suits for various customers’ demands. All below standard GN 500 GPM mud product is turnkey solution. The machine has lighting system and electrical control system for direct use.

Option 1: GNMS-500B mud recovery system, double deck shaker with 6m tank.0224 500gpm mud recycling system

It’s an economic standard system suits for customer who desires 500GPM system but don’t need large storage or very fine separation. The machine is by using 2 phase separation. It’s having a double deck shale shaker, with desilter cone on the top from the shale shaker. The underside screen can be used like a shale shaker and also the top deck screen utilized as a desilter. A mixing product is built within the system. There’s no agitator or mug gun for that system. It has compact design and effective price.

Option 2: GNMS-500G mud recovery system, shale shaker, and mud cleaner with 10m tank.

It’s 3 stage separation systems having a middle size storage tank. There’s a shale shaker because the 1rst stage separation. A mud cleaner with 1 ea. 10’’ desander cone and eight ea. desilter cone. A mixing product is built-in the machine. As well as an agitator along with a mud gun for that system.

Option 3: GNMS-500GL mud recovery system, shale shaker, mud cleaner with 12m tank.

GNMS-500GL mud recovery product is with similar equipment with GNMS-500G. Because the tank is larger size, there’s an additional agitator and mud gun for that system.

Normally, there are three methods for the desanding unit for connecting using the trenchless drilling rig

1) The standard condition is, the operator can search a mud pit at the drilling rig. Dirty mud from drilling rig would go to mud pit for settle lower first. You will see a slurry pump sump in to the mud pit and transfer mud from mud pit to shale shaker. After which, centrifugal pump can transfer mud from shaker tank to desander after which desilter.

2) An alternative choice is the fact that, you will see a little tank before shale shaker as alternative of mud pit. Dirty mud from well mind would go to the settle lower tank first, after which moved to shale shaker through slurry pump.

3) There’s several jobsite, the mud will flow to shale shaker from Horizontal directional drilling rig machine, much like gas and oil drilling rig. It’s not normal in horizontal directional drilling rig site layout.

Related Arciels:

3 phase Decanter Centrifuge for Oil Sludge Separation

3 phase decanter centrifuge is broadly utilized for oil sludge separation to release the dry solids and recovery oil weight loss as you possibly can, in the meantime, water is recycled for reuse. Before feeding, we need to heat the initial material to become liquidable.

You will find 2 situations:decanter centrifuge 3

1 The oil sludge comes from oil storage tank bottom or mud pit bottom, the majority of the sludge is okay solids, with this situation, 3 phase decanter centrifuge happens to be an option.

2 The oil sludge comes from drilling site; many of them are drilling cuttings, GNCD930 vertical cuttings dryer works by doing this. After separated by GN vertical cuttings dryer, the oil content around the cuttings is going to fewer than 5%, in certain nations, the solids could be landfilling, the recovered oil with water, fine solids could be separated by 3-phase decanter centrifuge or GNLW363VFD 2 phase decanter centrifuge to split up the fine solids and obtain clean oil.

We’ve both vertical cuttings dryer and 2 phase decanter centrifuge stocking in Houston for fast shipment and customer’s inspection and rental service. Please contact our sales in Houston at 713 320 3868/713 878 0880 for visiting.

Working principal of three phase decanter centrifuge:

3 phase decanter centrifuge can separate 3-phase: solids phase, light liquid phase, heavy liquids phase with the process below: Using the centrifugal G force, the heavies phase-solids phase is drived through the screw conveyor to small finish and released from solids discharge port, the solids is dry enough to become shipped by truck. The Two different density liquids will flow to large finish and released from various effluent port-heavy liquids port and lightweight liquids port. Therefore the different 3 phase are separated.

GN manufactured 2 phase separation decanter centrifuge is broadly utilized for drilling liquids strategy to solids control system and drilling waste management system.

Related Arciels:

500bbl mud storage tank for oil and gas drilling

500bbl mud storage tank is a common size mud tank for oil and gas drilling rigs. I can be used for mud mixing system or mud storage system. For HDD or CBM drilling, they normally do not use such big size mud tank.

Below is the parameters of GN design 500bbl mud storage tank, it is rectangular Mud Tank built as per API specification Schedule 40:28 E

Mud tank usable capacity: 500 bbl approx.

Compartment quantity: the 500bbls mud tank can be divided into 1~3 compartments (Depends on customer request.)

Capacity of each compartment: 250 bbl approx.

Mud tank dimension W x H x L: 13500×3000 x2650mm Or customized dimension.

Electrical agitator model GNJBQ150-DD, with 36″ impeller, 2-layer impeller. 20 HP driving motor, 460V – 60 HZ, RPM 1750 or 380V – 50 HZ, RPM 1450.

Electrical mud agitator quantity ¨C 2~4 each, with 2~4 each mud gun

Sufficient agitation to mix up 17 ppg mud. Bottom mud guns installed quantity ¨C 4 each. Bottom mud guns installed size 2 in, model GNNJQ50A-3G, 3-nozzle mud gun.

6″ suction and 4″ discharge line on either end of the tank with female cam lock connection to other tanks.

4″ drain line with butterfly valve – 2,

8″ Equalizing valve between compartments- qty 2~3. Depends on compartment quantity.

Cover with Grating top, collapsible hand rails surrounding, dual access- escape ladder

Skid: It is skid Mounted 3 runner oilfield skid with V crimp walls, it is easy for oilfield movement.

 

Other advantages of 500bbl mud storage tank for oil and gas drilling

  1. Sand Blast Treatment before painting.
  2. External paint and internal coating
  3. Bottom painting for anticorrosive: Two pack Epoxy zinc, thickness 75 ¦Ì
  4. Middle painting: Two Pack Epoxy hi-build containing anticorrosive pigmentstwice, thickness 250 ¦Ì
  5. Surface painting: Surface pigmented with high quality light fast PU pigments, thickness 70 ¦Ì
  6. Standard: API&ISO Certified Manufacturer

Related Arciels: