GN’s Slurry drilling mud system

GN Solids Control is probably the largest solid control as well as drilling waste management companies which usually specializes in manufacturing the similar equipment, such as shale shaker, desander, desilter, mud cleaner, vacuum degasser, mud gas separator, decanter centrifuge, agitator, centrifugal pump, cutting dryer, screw pump, shear pump, mud gun and so on. Immediately after 10 years development, GN offers promoted its products to 60 countries and now additionally, it established two overseas subsidiaries, US and Russia.

drilling mud system
Not long ago GN formally introduced the four solid control and also dewatering system, and slurry dredging system is one of these. Now we will introduce typically the configuration and some features to your account. According to the customer’s working situation and requirement, the system can be made into skid fastened or trailer mounted. The actual system mainly consists of the particular course shale shaker, desander, desilter, decanter centrifuge intended for 3 to 6 stages connected with separation according to customer’s demands. The working process is like this specific: the dredged slurry circulated from the pit or water tunnel, first the slurry will go through the scalping shale shaker, the solids such as trash, can, leaves, gemstone and so on will be separated through the slurry and the slurry may drop to a tank, then slurry will be sucked with the centrifugal to the desander, as well as desilter’shydrocyclone, in the hydrocyclone, typically the solids from 20-60 microns will be separated and dismissed and then dropped to the vibrating sex screens for further drying. The particular cleaner slurry will go straight into another tank then become pumped into the decanter centrifuge, and the solids over a couple of microns will be separated and also the cleaner slurry will be wiped away to the system. If possible, there may be another chemical decanter centrifuge to separate the solids near zero microns. The whole tools and configuration could be personalized per customer’s requirement in addition to working condition.
That’s the particular brief introduction of the slurry dredging system. Hopefully it can be useful to you. We will do our utmost to assist your business to be successful. This is visit http://www.gnsolidsamerica.com and please mail your inquiries to USA@gnsolidscontrol. com

Mud Gun & Mud Gun Pipeline in Solids Control System

When talking about a solids control system equipment, one must first thinks of shale shakers, desander and desilter cones and the decanter centrifuges, because the solids control means to control the solids phase particles. But no one could ignore the mud gun, which is small sized but not small functioned equipment.

GN Solids Control has a long history of designing and manufacturing solids control systems, in this article, we’ll talk about what’s the role the mud gun plays in a standard mud system.

What is a mud gun used for?

1, mud gun is used for helping the mud agitator to keep the drilling mud from settling. The mud agitator is located in middle of tank, and corresponding mud gun is on its side, for caring about the tank corners.

  1. for transporting drilling mud from one tank to any another. Of course, the mud gun can not achieve this goal all by its own, and it need help from the mud gun pipeline.

What does mud gun pipeline look like?

A mud gun pipeline is a 2 inch or 3 inch cubic pipe installed by the top frame of mud tanks. It covers nearly each tank of the system, except for the shaker tank. Because the drilling mud in shaker tank is not active mud, which can not be used directly in further drilling. But the drilling mud in other tanks, like active tank below the centrifuge, most times it could be used for mud pumps. Or mud in storage tank, if there is no need to add new materials into mud to change the proportion, the mud in storage tank can be used directly into further drilling.

Because the mud gun itself has no power to drive the mud, the mud gun line in fact is connected with the mixing pumps. When the user need to transfer mud via mud gun pipeline, he always shut down the connection between the mixing hopper and its centrifugal pumps, then the shear pumps is used to suck mud to mud gun line. By closing some tank’s mud gun lines, drilling mud is transferred to destination tank via mud guns.

GN Solids Control(website: http://www.gnsolidscontrol.com) is professional in such systems, and has lots of standard designs available to save the customers’ time. May you have such inquiry, welcome to contact us or visit our booth at Abu Dhabi Oil Show.

Go for GN Solids Control, Get the Best Solution: http://mengda0312.wordpress.com/2014/10/31/go-for-gn-solids-control-get-the-best-solution/